锰离子氧化沉淀法实现锂离子电池LiNi0.8Co0.05Mn0.15O2材料的回收和利用

以浓盐酸为浸出剂,以NaOH和NH₄HCO₃为沉淀剂,利用Mn²⁺在碱性条件下的氧化反应改变离子的沉淀次序进而分步回收的方案,探究了浓盐酸酸浸处理三元正极材料LiNi_0.8Co_0.05Mn_0.15O₂的最佳条件。在分步沉淀过程中,Mn²⁺被氧化为不溶于非还原性酸的MnO （OH）₂,并在酸性条件下回收。Ni、Co则在碱性条件下利用NaOH回收,而Li则利用NH₄HCO₃回收。该方法中Mn的回收率达到85.1%,产品纯度达到98.6%; Li的回收率达到95.0%,产品纯度达到99.3%。由回收材料重新合成的三元正极组装的软包电池的首圈放电比容量达到了175 mAh·g^-1,可以以超过99.5%的库仑效率稳定循环50圈。     

锂电池中的“锂键”效应

由于广泛存在,氢键在化学领域备受重视。“锂键”具有类似于氢键的一些性质,但锂的金属性和相对较大的原子半径,又使得“锂键”具有自己独特的一些特征。在氢键的基础上,介绍了“锂键”的概念、结构特点及其在锂电池中的应用,有助于人们深刻理解和应用“锂键”。考虑到“锂键”的新概念目前在化学教学中还较少涉及,期望今后可以适当增加“锂键”化学的相关知识,紧跟科技发展的潮流,进一步培养学生的科研创新意识。     

A Gel Polymer Electrolyte with 2D Filler-reinforced for Dendrite Suppression Li-Ion Batteries

Gel polymer electrolytes (GPEs) incorporate both the high ionic conductivity of organic liquid electrolyte and the high safety performance of all-solid-state electrolytes (ASSEs), greatly improving the electrochemical performance of solid polymer electrolytes (SPEs). However, the practical application of GPEs is still limited by inferior interface compatibility, lithium dendrites, etc. Herein, we prepared GPEs based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) further co-blended the two-dimensional sheet inorganic filler hectorite and poly(methyl methacrylate) (PMMA) to improve the mechanical and electrochemical properties of the GPEs. When the content of PMMA and hectorite is optimal, this GPEs have an ionic conductivity of 1.06×10⁻³ S cm⁻¹ and outstanding lithium symmetric cells cycle time of more than 3000 h, indicating that the introduction of filler effectively inhibits the growth of lithium dendrites at room temperature. Moreover, the GPEs adopt a relatively simple solution casting method to provide a fresh idea for the synthesis of high-performance GPEs.     

Amide-Based Ionic Liquid Electrolytes for Alkali-Metal-Ion Rechargeable Batteries

Ionic liquids (ILs) have a wide variety of applications in energy storage and material production. ILs are composed of only cations and anions, without any molecular solvents, and are generally known as “designer liquids (solvents)” because their physicochemical properties can be tuned by the combination of ionic species. In recent several decades, research and development activities of rechargeable batteries have garnered considerable attention because certain groups of ILs exhibit high electrochemical stability and moderate ionic conductivity, rendering them suitable for application in high-voltage batteries. ILs with amide anions are representative electrolytes and are extensively researched by many research groups, including our group. This paper focuses on amide-based ILs as electrolytes for alkali-metal-ion rechargeable batteries, introducing their history, characteristics, and existing challenges to be addressed.     

Porous inorganic filler Li4.7Ag1.63GeS4.8 in PEO electrolyte effectively inhibits Li dendrites for all-solid-state Li metal batteries

The newly created porous inorganic particles Li_4.7Ag_1.63GeS_4.8 as filler are added into poly (ethylene oxide) (PEO) with LiTFSI salt, which greatly improves the electrochemical stability of solid-state PEO-based electrolytes against Li metal in a working battery. Due to many pores and channels in the filler, Li dendrites would grow along these channels thereby effectively inhibiting their fast spread in PEO matrix and retarding the short circuit on account of the penetration of Li dendrite. The Li⁺ conductivity of this solid-state electrolyte membrane could be 1.36 × 10^-4 S/cm at 40 °C. The fabricated symmetrical Li metal cells could cycle above 550 h at 0.05 mA/cm² and corresponding LiFePO₄/Li all-solid-state cells have an excellent cycling stability of 160.65 mAh g^-1 specific capacity after 200 cycles with 99.93% columbic efficiency at 50 °C environment.     

葡萄糖对溶胶凝胶法制备Li1.2Ni0.13Co0.13Mn0.54O2正极材料性能的影响

利用XRD、SEM、EDS、BET、激光粒度、循环伏安、恒流充放电、交流阻抗方法研究了葡萄糖为碳源对溶胶凝胶法制备Li_1.2Ni_0.13Co_0.13Mn_0.54O₂正极材料的结构、形貌以及电化学性能的影响。结果表明:与前驱体中未加入葡萄糖所制备的材料相比,掺葡萄糖后样品颗粒分布相对均匀,粒径变小,D₅₀从11.56减小至9.94μm,比表面积增加近1倍。经0.05C充放电活化后,未掺葡萄糖和掺葡萄糖样品0.2C放电比容量分别为183.4、211.6mAh·g^-1,2C容量分别为其0.2C的62.2%、77.6%。1C循环50次后放电比容量分别为133.3、173.6mAh·g^-1,容量保持率分别为95.1%、100%。掺葡萄糖可降低首次不可逆容量损失,提高材料的倍率性能与循环稳定性,减少电荷传递阻抗、Warburg阻抗以及双电层弥散效应,但不改变材料的晶型结构。     

锂硫电池正极用硫/介孔碳复合材料的制备及电化学性能

制备了以十二烷基硫酸钠(SDS)为模板的介孔碳,并将介孔碳和单质硫采用熔融渗透法复合制得硫/介孔碳复合材料。SEM、TEM和BET结果显示介孔碳成直径约为500 nm的大小均一的球体,存在孔径为2 nm的微孔;单质硫充分填充在介孔碳的微孔中。以硫/介孔碳复合物作为锂硫电池正极材料时显示出高的电化学性能。初始放电容量高达1519 mAh·g^-1,在200 mA·g^-1的电流密度下充放电200个循环后依然能保持在835 mAh·g^-1。硫/介孔碳复合材料的高倍率性能和优异的循环稳定性,源于介孔碳良好的导电性及其孔结构的固硫作用。     

二价与四价金属离子等摩尔共掺杂的锂离子电池正极材料LiMn1.9Mg0.05Ti0.05O4的制备与表征

以氢氧化锂、乙酸锰、硝酸镁和钛酸丁酯为原料, 以柠檬酸为螯合剂, 采用溶胶-凝胶法制备了二价镁离子与四价钛离子等摩尔共掺杂的尖晶石型锂离子电池正极材料LiMn_1.9Mg_0.05Ti_0.05O₄. 采用热重分析(TGA), X射线衍射(XRD), 扫描电子显微镜(SEM), 透射电子显微镜(TEM)和电化学性能测试(包括循环伏安(CV)和电化学交流阻抗谱(EIS)测试)对所得样品的结构、形貌及电化学性能进行了表征. 结果表明: 780℃下煅烧12 h 得到了颗粒均匀细小的尖晶石型结构的LiMn_1.9Mg_0.05Ti_0.05O₄材料, 该材料具有良好的电化学性能, 在室温下以0.5C倍率充放电, 在4.35-3.30 V电位范围内放电比容量达到126.8 mAh·g^-1, 循环50 次后放电比容量仍为118.5mAh·g^-1, 容量保持率为93.5%. 在55℃高温下循环30次后的放电比容量为111.9 mAh·g^-1, 容量保持率达到91.9%, 远远高于未掺杂的LiMn₂O₄的容量保存率. 二价镁离子与四价钛离子等摩尔共掺杂LiMn₂O₄, 改善了尖晶石锰酸锂的电子导电和离子导电性能, 使其倍率性能和高温性能都得到了明显的提高.     

紫外分光光度法测定硫酸中的氮氧化物

建立了使用紫外分光光度法测定硫酸中氮氧化物的方法。利用高锰酸钾将试样中的亚硝酸根氧化成硝酸根,然后在硫酸(30%)介质中,于210nm波长处定量测定试样中氮氧化物的含量。方法检出限为0.0000075%,线性相关系数(r)为0.999 0,平均加标回收率为97.2%~102.8%,平均相对标准偏差(RSD,n=6)为2.9%~3.1%。方法灵敏度高、检出限低,操作简便、成本低,可应用于蓄电池电解液中氮氧化合物的检测。     

高中“化学反应与电能”跨学科项目式教学*——探究原电池电动势的影响因素

以“探究原电池电动势的影响因素”为项目学习主题,以探讨化学电源的应用、探究原电池的工作原理、测量原电池的电动势、搭建高电动势原电池等4个任务为关键项目任务,呈现高中“化学反应与电能”跨学科项目式教学设计思路和教学实践过程。